Ford Bronco Drive Shafts
Driveshafts
Tom Wood's Custom Drive Shafts - Utah
BE, BB, LB, II - Drive Shafts, U-joints, and drive train related parts
Front Dana 60 Axle Tech (Page 1)
Bronco U-Joints
U-Joint 3 7/8" Dana Spicer 1330 series u-joints
1980-96 Bronco
1980-96 Ford Truck
A corporate 14 bolt uses 1350 series u-joint and a stock driveshaft will fit with a 5" lift but will need a combination joint (half 1330 and half 1350) or a strip of plumber's tape around the joint on the 14 bolt side (not recommended for anything long term)
Combination u-joints can often be put together at a part's store by finding two different u-joints and switching the caps.
Front
1988-90 4 Speed Manual Transmission 105 wheel base
1988-90 C-6 Automatic Transmission
1990 E4OD Automatic Transmission 300 6 Cylinder
1990 E4OD Automatic Transmission 351-W V-8
Overall Compressed Length 39 3/8
Overall Extended Length 43 1/2
Rear
1988-89 Bronco C-6 A/T
compressed 29 1/8"
extended 33 1/4"
At rest - 89 Bronco, C-6, Borg Warner 1356, 14 bolt, shackle flip, 2" block - ~31"
U-Joint Info
U-joints come in a lot of different configurations and are manufactured by a lot of different companies.
Brand - For general use (both highway and heavy offroading), Warn industries has found that Spicer brand u-joints are superior to all other brands (the closest competitor was 85% the strength).
Solid Body U-Joint
Body Fitted Zerk Fitting
Capped Grease Fitting
Grease fitting configuration -
Solid u-joints without a grease fitting are the strongest, but often fail since they just don't get regreased. The seals will eventually fail and the joint will rust, squeak and then fail.
Grease fittings on the side of the u-joint are the most common setup for aftermarket u-joints and generally last longer since they can be easily regreased. Since there is a grease port in the body of the u-joint, it is weaker than the other two configurations listed here
Capped grease fitted u-joints are the better of the two above. They are much better for high impact loads than u-joints with body fitted grease fittings and can be lubricated to all for easy maintenance.
Size - bigger = better. Late model Broncos come with 1330 u-joints. 1350 are stronger and 1410 are stronger yet.
NOTE: D is the Ujoint cap diameter
E is the outside dimension across the joint from cap to cap
R is the diameter of the machined seal surface
Q is the length though the hole, and while not absolutely critical should be close o as to allow proper pinion nut tightening
S is the total "length" of the yoke, and as such, assuming Q is close, will affect driveshaft length slightly
Ujoint
series
Joint
width
E
Cap
dia.
D
U-bolt kit
Strap kit
Major
Diameter
Ground Hub diameter (R)
Length through hole (Q)
Centerline to end (S)
Joint Angle
Bearing Strap (BS) or U-bolt (UB)
Yoke plus slinger part #
Slinger part #
Yoke Part #
1310
3.219
1.062
2-94-28X
1.2760
1.8750
1.5000
2.5310
18.0
UB
2-4-3781X
30798
2-4-3771
2-70-18X
1.2760
1.8750
1.5000
2.9380
18.0
BS
2-4-3801-1X
34592
2-4-3791-1
2-94-28X
1.2760
1.8750
1.5000
2.9380
18.0
UB
2-4-3801X
34592
2-4-3791
2-70-18X
1.2760
1.8750
1.5000
2.9380
22.0
BS
2-4-6551-1X
34592
2-4-6541-1
2-70-18X
1.2760
1.8750
1.5000
2.9964
BS
2-4-8391-1X
34592
2-4-8331-1
1330
3.625
1.062
2-94-28X
1.2760
1.8750
1.5000
2.9380
20.0
UB
2-4-3671X
230421
2-4-3661
2-94-28X
1.2760
1.8750
1.5000
2.9690
UB
2-4-4291X
34592
2-4-4031
2-70-18X
1.2760
1.8750
1.7000
3.1880
BS
2-4-8421-1
1330-F
3.625
1.125
2-94-58X
1.2760
1.8750
1.5000
2.9380
18.5
UB
2-4-8051X
41195
2-4-8041
2-94-58X
1.2760
1.8750
1.5000
2.9380
20.0
UB
2-4-5311X
34592
2-4-5301
1350
3.625
1.188
3-70-28X
1.2760
1.8750
1.5000
3.0000
22.5
BS
3-4-12211-1
1.2760
1.8750
1.5000
3.0000
22.5
BS
3-4-5731-1X
34592
3-4-5721-1
1.2760
1.8750
1.5000
3.0000
22.5
BS
3-4-13031-1X
45799
3-4-12771-1
1.2760
1.8750
1.5000
3.0000
22.5
BS
3-4-13031-2X
45799
3-4-12771-2
1410
4.188
1.188
3-70-28X
1.2760
1.8740
1.4200
3.1850
22.5
BS
3-4-11891-1X
34592
3-4-11851-1
3-70-28X
1.2760
1.8750
1.5000
3.1880
22.5
BS
3-4-5711-1X
34592
3-4-5701-1
3-94-18X,
1.2760
1.8750
1.5000
3.1880
30.0
UB
3-4-8731
1480
4.188
1.375
3-70-38X
1.2760
1.8750
1.5000
3.5000
22.5
BS
3-4-13391-1X
34592
3-4-9531-1
7290
1.125
1.2760
1.8750
1.5000
3.3590
30.0
BS
2-4-7681-1X
34592
2-4-7671-1
Please feel free to link to this site so that others can find it. It's easy to link to this site, just copy one of the texts below onto your web page:
Copyright © 2000-2014